330905-05-08-10-01-00 | Bently Nevada 3300 NSv Proximity Probe

Bently Nevada 330905-05-08-10-01-00: 3300 NSv Proximity Probe Overview

• Manufacturer & Series: Bently Nevada, 3300 NSv Proximity Probes.
• Part Number: 330905-05-08-10-01-00 – M10x1 thread, no armor, 50mm unthreaded length.
• Case & Total Length: 80mm overall case length; total length 1.0 meter (39 inches).
• Connector Type: Miniature coaxial ClickLoc connector with protector, standard cable.
• Agency Approval: Option -00 (Not required).

Linear Range and Electrical Performance

• Linear Range: 1.5 mm (60 mils) from 0.25 mm to 1.75 mm (10 to 70 mils).
• Output voltage range: Approximately -1 to -13 Vdc over the linear range.
• Recommended Gap Setting: 1.0 mm (40 mils) from the target.
• Incremental Scale Factor (ISF): 7.87 V/mm (200 mV/mil), tolerance +12.5%/-20% including interchangeability.
• Deviation from Best Fit Straight Line (DSL): Less than ±0.06 mm (±2.3 mils).
• Probe DC Resistance: 4.2 ± 0.5 ohms for 1.0 meter length from center to outer conductor.

Frequency Response and Target Compatibility

• Frequency Response: 0 to 10 kHz typical, +0, -3 dB with up to 305 meters field wiring.
• Minimum flat target diameter: 8.9 mm (0.35 in); recommended minimum 13 mm (0.5 in).
• Small shaft note: Scale factor may change for shafts under 13 mm; reduce gap to limit change.
• Field Wiring: Use 0.2 to 1.5 mm² (16-24 AWG) or 0.25-0.75 mm² with ferrules.
• Recommended cable: Three-conductor shielded triad, max length 305 meters to Proximitor Sensor.

Environmental & Mechanical Specifications

• Operating Temperature: -52°C to +177°C (-62°F to +351°F).
• Storage Temperature: -52°C to +177°C (-62°F to +351°F).
• Probe Tip Material: Polyphenylene sulfide (PPS).
• Probe Case Material: AISI 304 stainless steel (SST).
• Probe Cable: 75 ohm coaxial, FEP insulated, available in 0.5, 1, 5, or 7 meters total probe length.
• Minimum Bend Radius: 25.4 mm (1.0 inch) with or without stainless steel armor.
• Maximum Torque on M10x1 threads: 0.56 N•m (5 in•lb) finger-tight; case threads first three threads max 22.6 N•m (200 in•lb).
• Pressure Seal Design: Viton O-ring seals differential pressure; probes not pressure tested before shipment.

Extension Cable Electrical Data and Installation

• Extension Cable DC Resistance: Center conductor 0.220 Ω/m (0.067 Ω/ft); shield 0.066 Ω/m (0.020 Ω/ft).
• Extension Cable Capacitance: 69.9 pF/m (21.3 pF/ft) typical.
• Recommended Torque for Probe Installation: Finger tight, never exceed 0.56 N•m (5 in•lb).
• Maximum Thread Engagement Length: M10x1 case thread allows up to 15 mm engagement.
• Compatibility: Fully interchangeable with previous 3300 RAM probes and extension cables.
• Increased Chemical Resistance: Superior to 3300 RAM, suitable for harsh compressor environments.

Frequently Asked Questions (FAQ)

• Q: Is this probe brand new and original?
  A: Yes. We supply only new original 3300 NSv Proximity Probes in factory packaging with full traceability.
• Q: Do you have the 330905-05-08-10-01-00 in stock?
  A: Yes, we keep this model in stock for immediate dispatch.
• Q: How long does delivery take?
  A: We ship within 5 days via FedEx, UPS, or DHL. Transit time depends on your location.
• Q: What is the linear range of the 3300 NSv probe?
  A: The probe provides a 1.5 mm (60 mils) linear range from 0.25 mm to 1.75 mm from target.
• Q: Can I use this probe with older Bently Nevada systems?
  A: Yes. The 3300 NSv is mechanically and electrically compatible with 3300 RAM proximity systems.
• Q: What is the recommended gap setting?
  A: Bently Nevada recommends a 1.0 mm (40 mils) gap for optimal performance.
• Q: Does the probe support high temperature?
  A: Yes. Operating range spans -52°C to +177°C (-62°F to +351°F).
• Q: What field wiring length works best?
  A: You can use up to 305 meters (1000 feet) of shielded triad cable without significant signal rolloff.
• Q: Can I return the probe if it doesn't fit?
  A: Yes. We support 30-day returns for items in original, uninstalled condition.
• Q: Is the probe pressure tested before shipping?
  A: Standard probes do not receive pressure testing. Contact our custom department if you need this service.

Contact Information Inquiries: Email us at sales@nex-auto.com or call +86 153 9242 9628 (WhatsApp). We are ready to support your 3300 NSv Proximity Probes order.

Partner NexAuto Technology Limited : https://www.nex-auto.com/