330103-08-15-10-02-00 Bently Nevada 3300 XL 8 mm Probe

330103-08-15-10-02-00 Bently Nevada 3300 XL 8 mm Proximity Probe

Key Technical Specifications

• Brand: Bently Nevada
• Model: 330103-08-15-10-02-00
• Series: 3300 XL 8 mm Proximity Probes
• Category: Proximity Probe / Eddy Current Sensor
• Probe Type: 3300 XL 8 mm, M10 x 1 thread, without armor
• Unthreaded Length: 80 mm
• Overall Case Length: 150 mm
• Total Length: 1.0 meter (3.3 feet)
• Connector Type: Miniature coaxial ClickLoc connector with standard cable
• Agency Approval: Not required
• Probe Tip Material: Polyphenylene sulfide (PPS)
• Probe Case Material: AISI 303 or 304 stainless steel (SST)
• Nominal DC Resistance: 7.59 Ω ± 0.50 Ω from center conductor to outer conductor at 1.0 m
• Linear Range: 2 mm (80 mils), starting at 0.25 mm (10 mils) from target
• Linear Range Voltage: Approximately –1 to –17 Vdc
• Recommended Gap for Radial Vibration: –9 Vdc (about 1.27 mm or 50 mils)
• Field Wiring: 0.2 to 1.5 mm² (16 to 24 AWG), 3-conductor shielded triad cable recommended
• Maximum Field Wiring Length: 305 meters (1,000 feet) between Proximitor sensor and monitor
• Probe Weight: 323 g/m (11.4 oz)

Temperature and Environmental Performance

• Standard Probe Temperature Range: –52°C to +177°C (–62°F to +350°F)
• Extended Temperature Range (Probe Tip): –52°C to +218°C (–62°F to +425°F)
• Extended Temperature Range (Cable and Connector): –51°C to +260°C (–60°F to +500°F)
• Low Temperature Caution: Temperatures below –34°C (–30°F) may cause premature pressure seal failure
• Relative Humidity: Less than 3% change in Average Scale Factor (ASF) after 93% humidity for 56 days per IEC 68-2-3
• Pressure Seal: Viton® O-ring seals differential pressure between probe tip and case
• Pressure Testing: Probes are not pressure tested before shipment; contact custom design for pressure seal testing

Hazardous Area Approvals

• Intrinsic Safety (ia): Class I, Zone 0: AEx/Ex ia IIC T5…T1 Ga; Class I, Groups A, B, C, D; Class II, Groups E, F, G; Class III
• Nonincendive (nA, ec): Class I, Zone 2: AEx/Ex nA IIC T5…T1 Gc; Class I, Division 2, Groups A, B, C, D; Class I, Zone 2: AEx/Ex ec IIC T5…T1 Gc
• Installation Requirement: Use intrinsically safe zener barriers per drawing 141092 or galvanic isolators
• Nonincendive Installation: Connect per drawing 140979 for nonincendive circuits

Temperature Classification Schedule (Probe Only)

• EPL Ga and Gc – T1: Ambient –55°C to +232°C
• EPL Ga and Gc – T2: Ambient –55°C to +177°C
• EPL Ga and Gc – T3: Ambient –55°C to +120°C
• EPL Ga and Gc – T4: Ambient –55°C to +80°C
• EPL Ga and Gc – T5: Ambient –55°C to +40°C
• EPL Dc – T280°C @ Ta: Ambient –55°C to +232°C
• EPL Dc – T225°C @ Ta: Ambient –55°C to +177°C
• EPL Dc – T170°C @ Ta: Ambient –55°C to +120°C
• EPL Dc – T130°C @ Ta: Ambient –55°C to +80°C
• EPL Dc – T105°C @ Ta: Ambient –55°C to +100°C
• EPL Dc – T90°C @ Ta: Ambient –55°C to +40°C

Installation Guide

• Mount the probe with an M10 x 1 thread and respect the 15 mm maximum thread engagement.
• Set the radial vibration gap to –9 Vdc, which equals about 1.27 mm (50 mils).
• Use 3-conductor shielded triad cable for field wiring and keep tinned connections.
• Keep field wiring under 305 meters (1,000 feet) to avoid high-frequency signal rolloff.
• Apply the recommended torque of 11.2 N·m (100 in·lbf) for standard forward mounted probes.
• For the first three threads, use a maximum torque of 22.6 N·m (200 in·lbf) and a recommended 7.5 N·m (66 in·lbf).
• Connect the probe to a 3300 XL Proximitor sensor and monitor for proper signal output.
• Avoid exposing the probe to temperatures below –34°C (–30°F) to protect the pressure seal.

Package List

• 1 x Bently Nevada 330103-08-15-10-02-00 3300 XL 8 mm Proximity Probe
• 1 x Miniature coaxial ClickLoc connector with standard cable (1.0 meter total length)
• 1 x Viton® O-ring pressure seal (installed)
• Protective packaging for safe transport

Shipping

• We ship worldwide via FedEx, UPS, and DHL.
• Orders leave our warehouse within 5 days after payment confirmation.
• We provide tracking information once the carrier picks up your package.

FAQ

• Q: What is the linear range of the 330103-08-15-10-02-00 probe?
  A: The linear range is 2 mm (80 mils), starting at 0.25 mm (10 mils) from the target.
• Q: What gap setting do you recommend for radial vibration?
  A: Set the gap to –9 Vdc, which is approximately 1.27 mm (50 mils).
• Q: What is the operating temperature range for the standard probe?
  A: The standard probe operates from –52°C to +177°C (–62°F to +350°F).
• Q: Can I use this probe in hazardous areas?
  A: Yes, with proper intrinsic safety barriers or galvanic isolators per drawing 141092.
• Q: What is the maximum field wiring length?
  A: You can run up to 305 meters (1,000 feet) between the Proximitor sensor and monitor.
• Q: What is the nominal DC resistance of this probe?
  A: The nominal resistance is 7.59 Ω ± 0.50 Ω at 1.0 meter.
• Q: What connector type does this probe use?
  A: It uses a miniature coaxial ClickLoc connector with standard cable.
• Q: Is the probe pressure tested before shipment?
  A: No, probes are not pressure tested before shipment. Contact custom design for pressure seal testing.
• Q: What is the recommended torque for installation?
  A: Use 11.2 N·m (100 in·lbf) for standard forward mounted probes.
• Q: What is the probe tip material?
  A: The probe tip uses polyphenylene sulfide (PPS).
• Q: Do you have this item in stock?
  A: Yes, we have it in stock and ready to ship.
• Q: What is your return policy?
  A: We support 30-day returns.
• Q: Is this product new and original?
  A: Yes, it is brand new and original.

Contact Information

Inquiries: sales@nex-auto.com or +86 153 9242 9628

Partner NexAuto Technology Limited: https://www.nex-auto.com/