330101-37-57-10-02-05 Bently Nevada 8mm Probe 3300 XL

Bently Nevada 3300 XL 8 mm Probe: Precision Vibration Sensing

• Brand & Model: Bently Nevada 330101-37-57-10-02-05 (3300 XL 8 mm Probe).
• Thread Type: 3/8-24 UNF without armor for direct mounting.
• Unthreaded Length: 3.7 inches (option 37) for precise tip positioning.
• Overall Case Length: 5.7 inches (option 57) to suit various gap settings.
• Total Cable Length: 1.0 meter (3.3 feet) with miniature coaxial ClickLoc connector.
• Agency Approvals: CSA, ATEX, IECEx (option 05) for hazardous locations.
• Nominal DC Resistance: 7.59 ± 0.50 Ω (center to outer conductor).
• Incremental Scale Factor (ISF): 7.87 V/mm (200 mV/mil) ±5% over 0°C to +45°C.
• Linear Range: 2 mm (80 mils) from 0.25 mm to 2.3 mm (-1 to -17 Vdc).
• Recommended Radial Vibration Gap: -9 Vdc (approx. 1.27 mm / 50 mils).
• Probe Tip Material: Polyphenylene sulfide (PPS) for chemical resistance.
• Probe Case Material: AISI 303 or 304 stainless steel (SST).
• Operating Temperature (Standard Probe): -52°C to +177°C (-62°F to +350°F).
• Extended Temperature (Tip Only): Up to +218°C (+425°F) for the probe tip.
• Relative Humidity: <3% change in scale factor after 56 days at 93% RH (IEC 68-2-3).
• Maximum Thread Engagement: 0.563 inches for 3/8-24 UNF case thread.
• Recommended Mounting Torque: 11.2 N·m (100 in·lbf) for standard forward mount.
• Cable Pull Strength: 330 N (75 lbf) due to patented CableLoc design.
• Extension Cable Capacitance: 69.9 pF/m (21.3 pF/ft) typical.
• Field Wiring Length: Up to 305 meters (1000 feet) between sensor and monitor.

Frequently Asked Questions (FAQ)

• Q: Is this 330101-37-57-10-02-05 a genuine Bently Nevada part?
  A: Yes, it is a brand new, authentic 3300 XL 8 mm Probe made in the U.S.A.
• Q: Can I use this probe with a 9-meter extension cable?
  A: Yes, but the system scale factor becomes ±6.5% instead of ±5%.
• Q: What happens if I expose the probe below -34°C?
  A: Low temperature may cause premature failure of the Viton pressure seal.
• Q: Does this probe work in ATEX Zone 0?
  A: Yes, with agency approval option 05 (CSA, ATEX, IECEx) it suits hazardous areas.
• Q: How do I clean the probe tip?
  A: Use a soft cloth with mild solvent; avoid scratching the PPS tip surface.
• Q: What is the maximum field wiring length from sensor to monitor?
  A: You can run up to 305 meters (1000 feet) of 3-conductor shielded triad cable.
• Q: Do you offer technical support for mounting?
  A: Yes, contact our team for recommended torque and gap setting assistance.
• Q: How long does delivery take?
  A: We ship within 5 days via FedEx, UPS, or DHL. Delivery time depends on your location.

Contact Information: For inquiries, email sales@nex-auto.com or call +86 153 9242 9628 (WhatsApp).

Partner: NexAuto Technology Limited